Results 1 to 3 of 3

Thread: EQ a begginers guide

  1. #1
    Join Date
    Sep 2009
    Posts
    287
    Thanked: 0
    Downloads
    1
    Uploads
    0

    Default EQ a begginers guide

    like my previous post anatomy of a kick i found this when i was starting out its only usefull as a rough guide obviously taste has alot to do with it but if youre looking for something to get you started with EQ read on .....

    50Hz
    Boost: To thicken up bass drums and sub-bass parts.
    Cut: Below this frequency on all vocal tracks. This should reduce the effect of any microphone 'pops'.

    70-100Hz
    Boost: For bass lines and bass drums.
    Cut: For vocals.
    General: Be wary of boosting the bass of too many tracks. Low frequency sounds are particularly vulnerable to phase cancellation between sounds of similar frequency. This can result in a net 'cut of the bass frequencies.

    200-400Hz
    Boost: To add warmth to vocals or to thicken a guitar sound.
    Cut: To bring more clarity to vocals or to thin cymbals and higher frequency percussion.
    Boost or Cut: to control the 'woody' sound of a snare.

    400-800Hz
    Boost: To add warmth to toms.
    Boost or Cut: To control bass clarity, or to thicken or thin guitar sounds.
    General: In can be worthwhile applying cut to some of the instruments in the mix to bring more clarity to the bass within the overall mix.

    800Hz-1KHz
    Boost: To thicken vocal tracks. At 1 KHz apply boost to add a knock to a bass drum.

    1-3KHz
    Boost: To make a piano more aggressive. Applying boost between 1KHz and 5KHz will also make guitars and basslines more cutting.
    Cut: Apply cut between 2 KHz and 3KHz to smooth a harsh sounding vocal part.
    General: This frequency range is often used to make instruments stand out in a mix.

    3-6KHz
    Boost: For a more 'plucked' sounding bass part. Apply boost at around 6KHz to add some definition to vocal parts and distorted guitars.
    Cut: Apply cut at about 3KHz to remove the hard edge of piercing vocals. Apply cut between 5KHZ and 6KHz to dull down some parts in a mix.

    6-10KHz
    Boost: To sweeten vocals. The higher the frequency you boost the more 'airy/breathy' the result will be. Also boost to add definition to the sound of acoustic guitars or to add edge to synth sounds or strings or to enhance the sound of a variety of percussion sounds. For example boost this range to:
    Bring out cymbals.
    Add ring to a snare.
    Add edge to a bass drum.

    10-16KHz
    Boost: To make vocals more 'airy' or for crisp cymbals and percussion. Also boost this frequency to add sparkle to pads, but only if the frequency is present in the original sound, otherwise you will just be adding hiss to the recording.

    Specific Instruments

    Vocals
    General: Roll off below 60Hz using a High Pass Filter. This range is unlikely to contain anything useful, so you may as well reduce the noise the track contributes to the mix.
    Treat Harsh Vocals: To soften vocals apply cut in a narrow bandwidth somewhere in the 2.5KHz to 4KHz range.

    Get An Open Sound: Apply a gentle boost above 6KHz using a shelving filter.

    Get Brightness, Not Harshness: Apply a gentle boost using a wide-band Bandpass Filter above 6KHz. Use the Sweep control to sweep the frequencies to get it right.

    Get Smoothness: Apply some cut in a narrow band in the 1KHz to 2KHz range.

    Bring Out The Bass: Apply some boost in a reasonably narrow band somewhere in the 200Hz to 600Hz range.

    Radio Vocal Effect: Apply some cut at the High Frequencies, lots of boost about 1.5KHz and lots of cut below 700Hz.

    Telephone Effect: Apply lots of compression pre EQ, and a little analogue distortion by turning up the input gain. Apply some cut at the High Frequencies, lots of boost about 1.5KHz and lots of cut below 700Hz.

    Hi-Hats
    Get Definition: Roll off everything below 600Hz using a High Pass Filter.
    Get Sizzle: Apply boost at 10KHz using a Band Pass Filter. Adjust the bandwidth to get the sound right.
    Treat Clangy Hats: Apply some cut between 1KHz and 4KHz.

    Bass Drum
    General: Apply a little cut at 300Hz and some boost between 40Hz and 80Hz.
    Control The Attack: Apply boost or cut around 4KHz to 6KHz.
    Treat Muddiness: Apply cut somewhere in the 100Hz to 500Hz range.

    Guitar
    Treat Unclear Vocals: Apply some cut to the guitar between 1KHz and 5KHz to bring the vocals to the front of the mix.
    General: Apply a little boost between 100Hz and 250Hz and again between 10KHz and 12KHz.

    Acoustic Guitar
    Add Sparkle: Try some gentle boost at 10KHz using a Band Pass Filter with a medium bandwidth.

    General
    Try applying some mid-range cut to the rhythm section to make vocals and other instruments more clearly heard.

  2. #2
    Join Date
    Jan 2009
    Location
    United Kingdom
    Posts
    262
    Thanked: 0
    Downloads
    48
    Uploads
    0

    Thumbs up

    Very useful guide mate i think we can all learn something from that Eq can change so many dynamics in the song

  3. #3
    Join Date
    Sep 2009
    Posts
    287
    Thanked: 0
    Downloads
    1
    Uploads
    0

    Default

    cant remember think i found this on d.o.a. some good stuff on there

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. The Ultimate Guide to Music PR
    By Urban Dubz in forum Promote Here
    Replies: 0
    Last Post: 29-06-2014, 10:46
  2. [BCT0030] ''FOND - Travel Guide'' Out Now!!!
    By bomber bc in forum Promote Here
    Replies: 0
    Last Post: 25-03-2013, 17:34
  3. Hey guys we're working on a guide for Music composers
    By Drue47 in forum Producers - Productions
    Replies: 0
    Last Post: 03-01-2011, 19:59
  4. Clubbing Guide London A to Z
    By infamous in forum Raving - Clubbing - Parties - Nightlife
    Replies: 0
    Last Post: 07-08-2010, 18:26
  5. anatomy of a kick - begginners guide
    By ratling in forum Producers - Productions
    Replies: 1
    Last Post: 08-04-2010, 23:21

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Visit Our Social Networks

Facebook DubplatesMyspace DubplatesYoutube DubplatesTwitter Dubplates